Here are three of the most common things that interfere with Wi-Fi signals and how to correct them. There are plenty of things, though, that can weaken or interfere with Wi-Fi signals in your home. That’s because most people now do their shopping online, consult with doctors online, work from home, stream entertainment and more.Īs most people rely on Wi-Fi as their primary means of connecting to the internet, getting and keeping a solid signal is critical. Squirty foam injected via holes along the bottom of the skirting board sounds a bad idea given the electrics are down there.These days, a reliable internet connection is more than just a convenience, it’s a necessity. I wonder how installers, or a DIY'er, would solve the problem of sealing gaps between the wall and the floor in tenements where you can't access from below? Or in fairly common cases like ours, where we've got the ground floor of a big villa that's been split into three (so a basement flat below and double upper above).Ĭould check if there were a problem quite easily with a cheap endoscope and some exploratory holes drilled in the skirting board, but not sure what you'd do if gaps were found. Many are owned by housing associations, and you'd think they'd be big potential clients. Think of all the tenements and other stone built buildings in Scotland's big cities, where you can otherwise do bugger all to green them much, especially in conservation areas. the one where I put stuff I'm not sure I'll ever get to). Not sure I understand what you mean by “carbon bead” Wouldn’t mind a whisper of the company in Glasgow or email (account details) for future reference. Therefore, if filling the gap between the wall & lath you will fill up the void below the floor if you don’t stuff them full.Īlso the studs are fixed to wedges into the lime mortar and often have extra x pieces so there’s quite a bit in the way so I would expect a number of injection points as per cavity installation and quite a bit of blowing it around. So there’s pretty much a straight through drop down to the sub floor void. I have found that in this case the boards tend to stop about 2inch off of the wall. However, often the joist often sits on a wider section of the wall below floor level. So if you have access from below via the sub floor void you can stuff from there. ![]() If they are built in to the wall then the floor boards probably extend to quite close to the wall, then the studding is above that. ![]() If not we may have to blast the space with a wood chip boiler or log boiler (wood chip supplier and plenty of logs on the island).Ĭheck how the floor joists are supported. ![]() If we can get insulation levels up we will consider GSHP. We will probably use £3000-3500 this year on oil. We are alos topping up attic and floor insulation and the house has DG fitted in 2001. The walls are in good nick and I haven’t detected any damp yet. If a moisture barrier is needed could one be painted/added from the inside during the decorating process? What happens at the top and bottom of the wall? How would you stop floor voids filling up with insulation? Is there any risk of condensation (dew point) forming on joist ends with the bead insulation in situ? Is there any danger of water ingress from outside to the inside? Would the beads still allow for sufficient ventilation within the cavity? Has anybody had any experience with this technique or know of insulation companies who do? This in theory would still allow 10% air movement around he cavity and shouldn’t have any issues with water absorption like blown cellulose or glass fibre Outside the house is dressed granite stone so EWI is out there as we are in a conservation area.Īn idea I am trying to get advice on is whether we could inject carbon bead insulation at lower pressure from the inside to fill the 3-4’’ cavity behind the lath and plaster. There are lots of period details in the 10 and 12ft high rooms, which include some v elaborate cornice, which we want to preserve if possible. Internally is lined with a lath and plaster on 3-4’' studs. ![]() Its a solid walled 1840's Victorian house. We have just moved into our house in the inner Hebrides.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |